Construction Rating: | starstarstarstarstar_border |
Flight Rating: | starstarstarstarstar |
Overall Rating: | starstarstarstarstar_border |
Manufacturer: | Quest |
Brief:
4FNC skill level 1 easy build kit with plastic fin can.
Construction:
The kit comes in plastic bag with:
I selected this kit for a rocket build I was doing with kids between the ages of 7-11, and most of them had never built a rocket before. I was looking for a rocket that allowed easy packing of a parachute, a rocket large enough to see all stages of flight, and one that would not frustrate first time builders with balsa fin problems. This rocket seemed to fit that description.
The assembly begins with constructing the motor mount. This included placing the engine hook in an already slotted motor mount, gluing in an engine block, taping the hook, adding the Kevlar® around the motor mount, and gluing the centering rings. Once the engine mount was dry, I tied the shock cord to the Kevlar® and then glued the motor mount assembly inside the body tube.
Next, I placed some plastic cement inside the fin can and slid it on to the body tube so that it was flush with the end. All I had to do now was tie the shroud lines on the parachute, attach the shock cord to the nose cone, and tie the parachute to either the shock cord or the nose cone.
The only change I made to construction was to add a swivel hook to the parachute to lessen any twisting of the chute.
The only real gotcha: the instructions were not clear which was the top and bottom of the fin can. I ended up gluing the fin can on the rocket upside down. As you might guess, this rocket is pretty foolproof, and the rocket performs fine with the fin can inverted. The only way I could tell which was the correct side of the fin can was to study the face card in the rocket kit bag.
Finishing:
Since this is on the really low end of the Level 1 spectrum, there is no
painting involved. All I did was add the stickers to the body tube and it was
ready to fly. Sticker decals are cheesy and these look no less cheesy than any
others. However, the kids I was working with really enjoyed the stickers and
they all tried to find creative ways to put them on their rockets.
Construction Rating: 4 out of 5
Flight:
I flew this rocket three times and all flights were successful. The first
flight was on an A8-3. What I like about the Bright Hawk is that Quest designed
a launch channel/lug directly into the fin can. It is easy to just slide it
right on the launch rod. The rocket, due to its size, struggled off the pad and
flew maybe 50-70 feet. The parachute opened in time and recovered nicely.
The next 2 flights were on B6-4s. The ascent was very straight, great altitude for athletic field flying, and the parachute brought it down nice and easy.
The fin can can take a beating. The parachute is a good size for the rocket. The size of the rocket allows it to be viewed in all aspects of flight.
Recovery:
This is a really easy kit to prep on the field. It is simple for kids to fold
the parachute and place it in the body tube without worrying about jamming a
chute inside a tiny tube. I look forward to flying with the kids in my rocket
build.
Summary:
PROs: A good, simple design that requires minimal, basic building. A good
introduction to the hobby of model rocketry. Fin can contains a launch lug, so
there is no need to add one on.
CONs: There was some confusion about the direction of the fin can. Also, the sticker decals are cheesy (but easy to apply!) Rocket flies well, despite the fin can being upside down.
Overall Rating: 4 out of 5
Brief: Quest's Bright Hawk is a good example of a Skill Level .5 rocket. (It's listed as a Skill Level 1, but its plastic fin can makes that a bit of a stretch.) Big and sturdy with a brightly colored plastic fin can and nose cone, it might be one of the better rockets currently available to gradually step up with if your previous experience has all been with RTF rockets. ...
Brief: Single stage, parachute recovery, skill level 1 kit that featuring a plastic nose cone and fin can, making assembley virtually foolproof. Construction: Bought the Bright Hawk kit at a Hobby Lobby 40% off sale in order to have something extremely simple that I could build with my 4 year old daughter without having to worry about anything getting messed up. This kit appeared ...
Sponsored Ads