Published: | 2011-12-01 |
Manufacturer: | Modification |
What is it about the Fat Boy, Onyx, Minie Magg, etc, that makes grown men's knees weak? I don't know, but the Big Daddy has it - and lots of it.
I swung by Commonwealth Displays a couple of times, but they were out of the kit. The second time I was beat out by a telephone order by an hour or so. I was ordering a few things from A to Z hobbies, and they had them in stock, so.....Two days later a box arrived. Inside were all sorts of goodies, but best of all, TWO BIG DADDIES!
I opened one up immediately, and test fit the fins, nose cone, etc. together. 3" diameter isn't all that much larger than 2.6" until you put it side by side with a Fat Boy. I was planning to make it stock, but after some thought, I sliced off about 1.75" of the BT to use on a scratch built Aries - which needed a 3" bit on the bottom. After looking at it again, I decided to slice off some more - by this time I had taken off 3.5" - and it looked even better than before! I decided not to push my luck, as I was already looking at some nose cone mods.
I've come to the conclusion that sanding and filling fins is MUCH easier before they're on the rocket - especially with TTW fins like this. Die-cut balsa quality is typical, the balsa was nice and sturdy. Typical prep - sand BT, CA the end of the BT and the MMT, build per instructions. I had to do a little trimming on the fins so they would fit properly - the slots in the BT were a little tight.
The NC modification was straight forward - cut off the back 1", epoxy and tape the shock cord onto the inside of the NC and extended the MMT up into the nose - this will eliminate the need for any wadding, since the ejection will never hit the chute, etc directly - it will bounce off the inside of the nose cone first. I think.
Prime, paint, and finish. The stock decals were no longer going to fit. Hmm. In the same spirit as Andy Waddell's "YO BATF" I tried to come up with an anagram for "Big Daddy" which made sense. Bad Giddy? Biddy Gab? No luck. " Big Baddy" lost out to "Dig Baddy." Five minutes and a sharp Exacto later, the "Dig Baddy" was born.
Stable? I haven't tested it. My gut feeling is that the large swept fins will be more than enough to keep it stable. I'm still thinking I should swing test it to be sure. It has the original 24 mm mmt - I was thinking 29 mm, but in the end I figure a 24 mm RMS will be more than enough power - I left the fins balsa and everything else is stock, so it's very light. An F12-J should be ideal, given the size and weight.
What's the verdict? For sheer flying fun, a short fat rocket like this can't be beat. It's very visible, and the mods I made make it almost improbably stubby. For $20 or so, it seems a little expensive for Estes stuff, but it's a lot cheaper than HPR kits, and would be more than adequate for G-range engines with no mods (except the 29mm MMT, of course)
Brief: I modified the Big Daddy kit to replace the stock nose cone with a fixed nose cone made from a PET soft drink bottle; parachute deployment is from an open "mortar" mounted on the bottle opening. Rationale? I swiped the nose cone from a family member's Big Daddy kit to use in a building ...
How to Make a V-2 out of an Estes Big Daddy Frustrated with the lack of availability of an affordable V-2 kit, I started thinking of ways to come up with a cheap and easy kit-bash from an existing in production kit that wouldn’t involve a lot of money or time. I also wanted to make a ...
Brief: Modified Estes Big Daddy to fly on 29mm motors. Modifications: I started this project with a regular Estes Big Daddy. When I bought the kit I knew I wanted to mod it to a 29mm so I bought a motor tube and cut it to a length that would allow it to come up and touch the base of the nose ...
I've always liked the Estes Big Daddy, but even flying on an E just wasn't good enough. So I went about building this to fly on a H - the H128 specifically. Components Out of the box, the kit includes: Nose Cone Centering Rings Pre-Slotted Body Tube Motor Mount ...
A modification to the Estes Big Daddy to use much less wadding. Modifications: The Estes Big Daddy is a short, fat rocket. With this being the case, there is a large volume in the interior of the rocket that needs to be filled with wadding to protect the parachute. I am always looking for ...
I bought this Big Daddy (on sale, of course) as a test-bed for a Micro-Hybrid motor. This required an extension of the motor mount, and the capability to house electronics in the nose cone. Before flying it on a Micro-Hybrid, I'll probably try it on a conventional motor with motor ejection (1st ...
The Estes Big Daddy first caught my eye hanging on the rack at WV Hobbies in the fall of 1998. It looked to me to be a good candidate for conversion to 29mm power, so I put it on my Christmas list. My request was granted, and away I went. My first decision was to evaluate the kit parts to see ...
The Educator is a modified Big Daddy. The modifications include adding a 12" payload section and using basswood for fins and centering rings. Modifications: The first modifications were adding basswood fins and centering rings. The second modification was adding a payload section. This was ...
I was playing around with my Estes 'Big Daddy' one day when I discovered that its NC would fit the tube that my Aerotech Initiator came packed in. The decision was then made to acquire another Big Daddy and build the 3D Mega Daddy (3D MD). Components Only 3 components ...
Sponsored Ads